I have downloaded the drivers from the website and installed them sucessfully the STLink shows correct in device manager on my 64Bit Windows 10.
In the arduino IDE (1.8.10) I selected STLink as upload method. Unfortunately the STLink is not found. The Boot Jumpers on the Board are both on 0 (to the left). Upload via serial works with the jumper boot 0 = 1
Here the console output from the arduino IDE
Code: Select all
Compiling 'Test_STM32' for 'Generic STM32F103C series'
Program size: 14 212 bytes (used 22% of a 65 536 byte maximum) (1.81 secs)
Minimum Memory Usage: 3128 bytes (15% of a 20480 byte maximum)
Uploading 'Test_STM32' to 'Generic STM32F103C series' using 'COM17'
Uploader started for board Generic STM32F103C series
Upload method will be: bootloader
Uploading via Bootloader
Resetting to bootloader via Serial
Serial reset
Reset via USB Serial completed
C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win\stlink_upload.bat "C:\Users\roger\AppData\Local\Temp\VMBuilds\TEST_S~1\STM32D~1\Release/Test_STM32.ino.bin"
C:\Program Files (x86)\Arduino-1.8.10\java\bin>rem @echo off
C:\Program Files (x86)\Arduino-1.8.10\java\bin>rem: Note C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win\ get path of this batch file
C:\Program Files (x86)\Arduino-1.8.10\java\bin>rem: Need to change drive if My Documents is on a drive other than C:
C:\Program Files (x86)\Arduino-1.8.10\java\bin>set driverLetter=C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win\
C:\Program Files (x86)\Arduino-1.8.10\java\bin>set driverLetter=C:
C:\Program Files (x86)\Arduino-1.8.10\java\bin>C:
C:\Program Files (x86)\Arduino-1.8.10\java\bin>cd C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win\
C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win>rem: the two line below are needed to fix path issues with incorrect slashes before the bin file name
C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win>set str="C:\Users\roger\AppData\Local\Temp\VMBuilds\TEST_S~1\STM32D~1\Release/Test_STM32.ino.bin"
C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win>set str="C:\Users\roger\AppData\Local\Temp\VMBuilds\TEST_S~1\STM32D~1\Release\Test_STM32.ino.bin"
C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win>rem: ------------- use STLINK CLI
C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win>stlink\ST-LINK_CLI.exe -c SWD -P "C:\Users\roger\AppData\Local\Temp\VMBuilds\TEST_S~1\STM32D~1\Release\Test_STM32.ino.bin" 0x8000000 -Rst -Run -NoPrompt
The upload process has finished.
STM32 ST-LINK CLI v3.3.0.0
STM32 ST-LINK Command Line Interface
No ST-LINK detected!
C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win>rem: Using the open source texane-stlink instead of the proprietary STM stlink exe
C:\Users\roger\AppData\Local\arduino15\packages\stm32duino\tools\stm32tools\2020.5.16\win>rem:texane-stlink\st-flash.exe write "C:\Users\roger\AppData\Local\Temp\VMBuilds\TEST_S~1\STM32D~1\Release\Test_STM32.ino.bin" 0x8000000
Any help is very apprechiated