I tried this, but all it does is lights leds full white and nothing more, some suggestions?
Code: Select all
#include <WS2812B.h>
#include <SPI.h>
#include <nRF24L01.h>
#include <RF24.h>
#define NUM_LEDS 16
RF24 radio(PB0, PA4);
const uint64_t address = 0xF0F0F0F0E1LL;
/*
* Note. Library uses SPI1
* Connect the WS2812B data input to MOSI on your board.
*
*/
WS2812B strip = WS2812B(NUM_LEDS);
// Note. Gamma is not really supported in the library, its only included as some functions used in this example require Gamma
uint8_t LEDGamma[] = {
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1,
1, 1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 2,
2, 3, 3, 3, 3, 3, 3, 3, 4, 4, 4, 4, 4, 5, 5, 5,
5, 6, 6, 6, 6, 7, 7, 7, 7, 8, 8, 8, 9, 9, 9, 10,
10, 10, 11, 11, 11, 12, 12, 13, 13, 13, 14, 14, 15, 15, 16, 16,
17, 17, 18, 18, 19, 19, 20, 20, 21, 21, 22, 22, 23, 24, 24, 25,
25, 26, 27, 27, 28, 29, 29, 30, 31, 32, 32, 33, 34, 35, 35, 36,
37, 38, 39, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 50,
51, 52, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 66, 67, 68,
69, 70, 72, 73, 74, 75, 77, 78, 79, 81, 82, 83, 85, 86, 87, 89,
90, 92, 93, 95, 96, 98, 99,101,102,104,105,107,109,110,112,114,
115,117,119,120,122,124,126,127,129,131,133,135,137,138,140,142,
144,146,148,150,152,154,156,158,160,162,164,167,169,171,173,175,
177,180,182,184,186,189,191,193,196,198,200,203,205,208,210,213,
215,218,220,223,225,228,231,233,236,239,241,244,247,249,252,255 };
void setup()
{
/*Serial.begin(115200);
SPI.setModule(1);
radio.begin(); //Starting the Wireless communication
radio.openWritingPipe(address); //Setting the address where we will send the data
radio.setPALevel(RF24_PA_MIN); //You can set it as minimum or maximum depending on the distance between the transmitter and receiver.
radio.stopListening(); //This sets the module as transmitter
Serial.println("Successfully opened");
Serial.println("Set as transmitter");*/
SPI.setModule(2);
strip.begin();// Sets up the SPI
strip.show();// Clears the strip, as by default the strip data is set to all LED's off.
strip.setBrightness(35);
}
void loop()
{
/*const char text[] = "Your Radio is working";
radio.write(&text, sizeof(text)); //Sending the message to receiver
Serial.println("Sent");*/
pulseWhite(10);
}
void pulseWhite(uint8_t wait) {
for(int j = 0; j < 256 ; j++){
for(uint16_t i=0; i<strip.numPixels(); i++) {
strip.setPixelColor(i, strip.Color(LEDGamma[j],LEDGamma[j],LEDGamma[j] ) );
}
delay(wait);
strip.show();
}
for(int j = 255; j >= 0 ; j--){
for(uint16_t i=0; i<strip.numPixels(); i++) {
strip.setPixelColor(i, strip.Color(LEDGamma[j],LEDGamma[j],LEDGamma[j] ) );
}
delay(wait);
strip.show();
}
}